HHO Carbon Flame Metal Cutting Machine

HHO Carbon flame metal cutting machine SPECIFICATION Hydrogen oxygen cutting machine operating steps: 1. Start the gas production process: 1 Turn on the main power switch of the oxyhydrogen cutting machine; 2 Wait for the Hydrogen Oxygen Cutting Machine to carry out the system self-test; after...
  • HHO Carbon flame metal cutting machine

    SPECIFICATION

    Mode

    Specification

    GTHO-6500

    Input Voltage

    380 ±10%,50/60Hz,three phase

    Rated Capacity (KVA)

    22

    Working Gas Pressure (Mpa)

    ≤0.2

    Relative Humidity (%)

    90

    Rated  Gas Production (L/h)

    6500  ±10%

    Water  Consumption (L/h)

    3.8

    Maximum  Cutting Thickness (mm)

    200

    Effective Punching Thickness (mm)

    70

    Water Feed

    auto

    Cooling Mode

    Air  Cool

    The Insulation Level

    F

    Power  Supply Protection Grade

    IP21S

    Flame Temperature (℃)

    Adjustable  800~3200

    Working Medium

    Filtered  water or deionized water or soft water

    Working Method

    Continuous

    Enviroment Temperature (℃)

    0~40

    Outline Dimensions - L*W*H (mm)

    1300*930*1820

    Gross Weight (kg)

    520

    Ventilation Space Requirement (mm)

    400  in each direction


    Hydrogen oxygen cutting machine operating steps:

    1. Start the gas production process:

    1 Turn on the main power switch of the oxyhydrogen cutting machine;

    2 Wait for the Hydrogen Oxygen Cutting Machine to carry out the system self-test; after the self-test is complete, or report the [Fault Information] or [The system status is normal, press the F1 button to start the gas production]

    3 Press the F1 button to start gas production, adjust the gas production knob, you can adjust the gas production 4) When the machine pressure gauge shows a pressure of 0.2Mpa, the system automatically stops gas production


    2. Preheating

    1 Open the cutter's gas valve to the proper opening

    2 Try to test the amount of gas at the outlet of the cutting nozzle, and feel that there is a relatively large flow of gas before ignition. Otherwise, the opening of the gas valve must be adjusted to allow ignition.

    3 According to the operating instructions of the cutting machine, move the cutting nozzle to the edge of the steel plate so that half of the flame heats the steel plate and the other half of the flame remains outside the steel plate.

    4 Closely observe the condition of the heated surface of the steel plate. When the plate burns red and flies out of Mars, it can be cut.

    3. Cutting: When the surface of the steel plate reaches the cutting state, open the high pressure oxygen valve to the proper opening, and you can see that the steel plate is cut by the high pressure oxygen. This is to open the switch of the walking mechanism and let the cutting machine walk. Note: Before walking, It is necessary to adjust the cutting speed in advance according to the thickness of the steel plate. When walking, according to the cutting state of the steel plate surface, the walking speed and the oxygen pressure may also be adjusted. However, for experienced cutters, the oxygen pressure and walking are generally not adjusted. Speed, because adjusting these things during the cutting process will affect the cutting quality of the steel plate.

    4. One-cut operation: When the cutting line is completed, immediately close the high-pressure oxygen valve and close the walking switch to stop walking. And move the cutter to the next cutting point

    5. The cutting is completed, the flameout operation: open the low pressure oxygen valve, blow out the flame, and then close the gas valve, and then close the low pressure oxygen valve. Turn off the main power switch of the machine, then open the low-pressure oxygen valve, put the remaining gas inside the machine and then close the low-pressure oxygen valve.




    Hot Tags: HHO carbon flame metal cutting machine, China, manufacturers, buy, discount, quotation, in stock